biathlonmordovia.ru → Electrical installation

Smooth brick Bavarian masonry at an affordable price from the manufacturer. Scheme of Bavarian bricklaying Braer facing brick

In past centuries, due to imperfections in the firing process, finished products took on different shades, resulting in a heterogeneous appearance on the surface of houses. These days are colorful brick walls turned into a fashion trend, and such facade cladding began to be called Bavarian masonry, since its homeland is the southern state of Germany - Bavaria. German masons learned to combine blocks from different batches, creating unique “outfits”.

According to scientific terminology, a multi-color ceramic block is called “reduced fired flash brick.” To achieve the effect of non-uniform coloring, the factory periodically turns off the air supply to the furnace during heat treatment. At such moments, oxygen is removed from the clay to support combustion, and the surface temperature decreases.

At the last stage, the power of the air flow is increased, due to which the shell of the workpieces becomes very hot, releasing molecules of certain compounds from the clay and changing its color. Control of processing modes allows you to plan shades in advance. High-temperature firing improves the following properties:

increases strength and resistance to external loads;
the surface sinteres and becomes hard, like glass, and does not collapse under the influence of external factors;
frost resistance is 75-100 cycles;
water absorption is stabilized: for ordinary ceramic it varies between 6-14%, and for flash brick - 6.8-9.5% (in the presence of voids - up to 7.5%);
the thermal conductivity of hollow options is reduced to 0.19 W/m o C (for ceramic ones - 0.44 W/m o C);
Almost no efflorescence appears - the salts have time to decompose during the firing process.

“Motley” brick is more environmentally friendly compared to glazed (painted) brick. Flash technology maintains breathability. The only drawback of modernized ceramics is the high price, which can be explained by the complexity of the technology. Multi-colored blocks are also used for the outer row of load-bearing walls and for the manufacture of architectural elements under load.

Specifics of Bavarian masonry

To make the house original, it is enough to combine 3 to 5 shades of cladding. The more color options, the harder the job. The circuit can be calculated using special computer programs. Based on the calculation results, all that remains is to purchase the material in the required proportions at the factory or in the retail chain. Professional masons use their own techniques:

Bricks are taken not from one pallet, but from different ones - for example, from five.
The main tone is determined (its share is at least 50%), supplemented with auxiliary ones in an arbitrary ratio.
Several patterns are drawn on a sheet of whatman paper - rectangular areas containing the desired color ratio. Having made 5-10 fragments, combine them in various combinations and look for the best “random” pattern.
The wall is decorated only for jointing; it looks most impressive using colored mortar.
A private house looks unique if such masonry is used only for the design of door and window openings, arched vaults, and columns. This approach allows you not only to purchase the required quantity, but also to save money.
The cottage is original with a general motley background and monochrome corners.

In the classic version, preference is given to brown and red tones. Modern design ideas are based on a more diverse palette. The cottage looks original with alternating blue, gray and light yellow colors. If desired, you can buy smooth or textured facing bricks.

Review of brick manufacturers and assortment

Domestic enterprises that have mastered advanced technologies, equipped modern equipment and automated lines, they produce quite decent products suitable for Bavarian masonry.

1. Braer brick factory.

The main enterprise of the Braer group is a production complex located in the Tula region and has its own loam deposit (Obidimsky). The product catalog includes selections of standard sizes - 0.7 NF (euro, 250x85x65), 1NF (single, 250x120x65); 1.4NF (one and a half, 250x120x65 mm).

Not only smooth, but also textured models are produced: reef (with long straight grooves), oak bark (with asymmetrical short grooves). Recently, new items have appeared in the assortment - oak bark and corrugated with sand. White decorative sand is sprayed onto their surface, thanks to which the masonry shines under sun rays as if it were covered with frost.

Multi-colored facade material is traditionally presented in a rich range of colors:

mocha (taupe);
terra (red-brown);
Bordeaux;
red;
straw.

2. The Fifth Element.

The company is located in the Kaliningrad region. In terms of technical equipment and production volumes, the company is one of the leaders among domestic manufacturers of wall building materials, and the quality of the products meets the new GOST 530-212 and European regulatory document EN 771-1:2011.

Full-bodied. It is produced in one standard size - 1NF (single), has increased strength (M300), and a density of 1900-2000 kg/m3. Solid molded blocks are used for external walls, columns, chimneys, and fireplaces.
Hollow with a thickened wall. In this category, 3 types are produced: euro, single and one-and-a-half. Due to their fairly high strength class (from M175 to M200), they can be used both as cladding and for laying load-bearing walls. It is an effective heat insulator: the thermal conductivity coefficient does not exceed 0.193 W/m* o C.

Due to improved technology, the color palette has been expanded to 20 shades. The assortment includes smooth and rusticated (embossed) options. Private houses laid out from Rustic or Canyon look very expressive (collections differ in the depth and frequency of notches).

3. Magma Brick Factory.

This is a relatively new enterprise located in the Republic of Mordovia. For the production of products, an automated line from KELLER (Germany) is used. Using reduced firing technology, the following types of hollow block are produced:

single smooth;
one and a half smooth;
single Antique – rusticated, straw-colored, with light corrugation;
single Maple – gray-brown, with deep, randomly located furrows.

In terms of strength, flash products correspond to the M150 brand, the density is 1200 kg/m3, water absorption does not exceed 8%. Thermal conductivity is slightly higher than that of the Fifth Element - on average 0.39 W/m m * o C. Decent decorative qualities: no chipping, correct geometry. It is also recommended to buy Magma for cladding the above-ground part of fences: the masonry is quite dense and the water absorption is low.

Cost and characteristics

Prices from manufacturers for the main types of reduced-firing bricks.

Manufacturer	Characteristics	Price, rub/piece
Briar	Single, slotted, corrugated with sand, M150	22
	Single, slotted, oak bark, M150	29
	Single, slotted, grooved, M150	19
	Euro, slotted, smooth, M150	16
	One-and-a-half, slotted, smooth M150	28
The Fifth Element	Full-bodied, single, smooth	41
	Hollow, single, smooth	28
	Hollow, single, rustic	25
	Single smooth	20
Magma	One and a half smooth	27
	Single Antique	21
	Single Maple	21

Facing bricks from the Braer brand have won the recognition of many developers. Thanks to excellent performance characteristics, a large selection of colors, attractive appearance this material has received a wide range of applications, especially Braer Bavarian masonry.

Colored ceramic bricks from Braer are used for:

facade and interior finishing;
fireplace linings;
landscape design;
decorating the base, arches, columns and other architectural elements.

The facing brick of this brand is produced in a factory using advanced German equipment. Careful selection of raw materials, adherence to technology, strict output control - all this allows us to guarantee the exceptional quality of the finished product and reduce the likelihood of defects to zero. Facing brick The brayer is produced in accordance with GOST 530-2012, which confirms its strength, durability and environmental friendliness.

Braer Bavarian masonry: production features and advantages

Bavarian masonry is one of the varieties of decorative masonry, during which a certain pattern is formed through the use of bricks of different colors. Initially (in the 17th century), “variegated” masonry was a necessity, because it was difficult to obtain identical bricks in large quantities. We had to combine different shades of the face stone, creating harmonious combinations of color and texture. This idea quickly took root in European architecture, and Bavarian masonry took shape as an independent movement.

Different shades of ceramic bricks (up to 6-8) can be achieved due to uneven firing and oxygen starvation. At your disposal are “classic” face bricks in brown or red, as well as more modern options(from burgundy to straw and terracotta). The ESP company offers to buy building materials for every taste and color.

Regardless of the color scheme, Braer facing bricks are different:

durability (the service life of such cladding is more than 50 years);
resistance to low temperatures (more than 100 freezing/thawing cycles);
increased strength;
low degree of water absorption (which eliminates freezing, cracking, mold and mildew formation);
resistance to negative influence environment;
unpretentiousness in care.

Facing brick Braer from "ESP": large selection, fair prices

Bavarian masonry from Braer is available in several formats: 0.7 NF, 1 NF, 1.4 NF, which corresponds to the Euro format, single and one-and-a-half bricks, respectively. The price directly depends on the type of material and batch size. Each client is guaranteed to receive:

certified quality of materials;
competitive prices;
accurate execution of requests;
prompt supply of bricks in the required volume;
free advisory support at all stages of cooperation;
convenient terms of payment and delivery;
flexible system discounts for regular and wholesale customers.

The purpose of the external cladding of a house is to create a durable and aesthetically attractive shell of the house, protecting critical structural elements from the effects of precipitation, mechanical damage, etc.

In this regard, facing brick is one of the most reliable materials that performs all the necessary functions.

The cladding has normal look brickwork, natural for the walls of a building, but the quality of the material is much higher than that of ordinary brick, which allows you to create a durable and beautiful outer layer that cuts off external moisture and additionally insulates the walls.

The durability and reliability of facing bricks make its use attractive to users who value the stylish appearance and solidity of the material.

The Russian company Braer produces several types of facing ceramic bricks. The high quality of products is explained by constant quality control, the use of modern equipment and the improvement of production techniques.

The Braer company aims to produce products with the best quality in the world and spares no effort in achieving success. The abundance of facing materials has not reduced the demand for facing bricks as the most durable and reliable material.

Ceramic facing bricks are highly durable. The hollow structure of the block eliminates the accumulation of stress during firing, which reduces the possibility of cracks or destruction.

The even shape and precise geometric lines make possible high-quality masonry, creating a neat and stylish decorative cladding. The front side of the brick can have a smooth or textured surface, creating the effect of a rough or perfectly smooth wall.

The facing brick has several color options, as close as possible to the natural color of fired ceramics. One or more colors can be used to create a specific geometric pattern or the so-called Bavarian masonry, when the wall consists of several colors of brick, randomly and evenly distributed over the entire area.

There are 5 lines of material:

Red.
Muscat.
Brown.
Bordeaux.
Bavarian masonry.

Brayer brick is considered one of the best facing materials produced in Russia and fully meets all European quality standards.

Advantages and disadvantages of the material

Braer facing brick has the following advantages:

High strength.
Heat-saving properties due to the presence of cavities inside the block.
High decorative qualities.
Environmentally friendly material.
Low ability to absorb water.
Good tolerance to temperature changes.
High resistance to mechanical stress, shock, scratches, etc..
The durability of the material can compete with the life of the house.
Relatively low weight of the material, which does not create additional load on the foundation.
The cost of brick cladding, given its durability and the absence of the need to subsequently paint and repair the facade, is much lower than any other method of exterior finishing.

The disadvantages of facing bricks include:

Difficulty in installation. A well-built facade requires the involvement of qualified specialists with the appropriate skills and experience. Self-cladding is only possible with preparation.
Cladding work is carried out using wet compounds, which complicates the ability to finish the finished house.

Specifications

Brayer facing brick has the following parameters:

Format - 0.7NF, 1NF, 1.4NF.
Length - 240 mm.
Width 120 or 85 mm (0.7NF).
Height - 65 mm or 88 mm (1.4NF).
Weight - 1.7, 2.3, 3.1 kg.
Brand - 150-175 kgf/cm2.
Frost resistance - at least 100 cycles.
Water absorption - 8-9%.
Quantity in a pallet - 600 pcs.

Production technology

The technological production chain begins in the quarry where clay, which is the main raw material, is extracted. Production workshops are located 1 km from the quarry, which greatly simplifies logistics and also reduces production costs.

Clay is mixed with water and special additives that give the products additional properties and create texture. After this, the brick is shaped and sent for firing.

The firing technology is called flashing. Its essence is to limit the amount of oxygen when firing ceramics, allowing you to obtain different shades of color without the use of dyes. When burning in conditions of oxygen deficiency, a lot of carbon is produced, which, when burned, gives shades of blackness to the product.

The Braer kiln is 240 m long, one of the longest in Europe. Wide possibilities for firing the material are the basis for the high quality and specific properties of facing bricks.

Product quality control is carried out by our own laboratory, equipped with modern equipment. It allows for continuous quality monitoring, timely detection of technological deviations or regulation of the production process.

Bavarian masonry

Bavarian masonry is the use of several colors of brick on one plane. Previously, when firing bricks, it was impossible to achieve the same color for all blocks, so the craftsmen tried to evenly distribute bricks with a darker or lighter shade over the entire surface.

The wall turned out to be colorful, but this appearance turned out to be quite aesthetically attractive. The imperfection of technology, which in the old days everyone tried to avoid in every possible way, is today a sign of style and is widely used in exterior decoration houses, buildings, fences. Different techniques are used to create Bavarian masonry - using from 2 to 7 colors.

The Braer company produces a special type of brick - Bavarian masonry, which has the following varieties:

Corrugated with sand.
Smooth.
Oak bark with sand.
Mocha.
Terra.
Bordeaux.

PLEASE NOTE!

All varieties have several shades of color, allowing you to create a “ripple” effect of varying degrees of density. At the same time, the result obtained largely depends on the skill of the mason doing the masonry. The same set of bricks can be distributed in different ways, which may look natural to varying degrees.

Basic rules for creating Bavarian masonry:

Do not lay two bricks of the same color next to each other.
Before starting work, carefully sort the material, then mix it as evenly as possible by shade.
Distribute the available colors across the plane as evenly as possible, while avoiding exact repetition of the alternation of shades.

The rules are simple, but require some skill and experience in drawing up a drawing.. Sometimes the darkest (or lightest) bricks are placed in the corners, emphasizing and further decorating them, making the wall design more orderly.

Preparing the wall for cladding

Before starting work, you should make sure that the foundation is reliable and can withstand the additional load from the facing brick. This point is especially important for two-story (or more) houses that receive a significant increase in the mass of the walls.

The second important point will be to determine whether there is enough space to support the brick on the foundation. If you plan to install insulation about 5 cm thick, plus 3 cm of ventilation gap and plus 8 cm of brick width (the minimum support area must be at least 2/3 of the brick width), then a foundation strip of at least 16 cm wide will be required.

If this ratio is not maintained, the width of the base strip should be increased using steel angles attached to the foundation with anchors. It is also necessary to check the amount of eaves overhang, which should be increased if necessary. The protruding masonry will collect moisture into the voids and will be torn apart when frozen, so this issue should be resolved responsibly.

Preparatory work includes:

Actually preparing the surface.
Installation of insulation with waterproofing.
Formation of a ventilation gap.

Surface preparation is the removal of all foreign objects, filling of cracks or potholes in the surface. Wooden walls should be impregnated with an antiseptic composition.

Installing insulation will require the creation of a sheathing made of metal or wooden planks. The sheathing pitch is the width of the insulation slabs, which are inserted spaced between the planks. Additionally, the insulation is attached using fungi - special dowels with wide caps. A waterproofing membrane must be installed on top of the insulation.

The ventilation gap is 2-3 cm. It allows you to remove moisture from the wall material and insulation, keeping them dry and functional.

If non-vapor-permeable materials are used as insulation - polystyrene foam, polystyrene foam or EPS, a ventilation gap is not needed.

DIY styling

Bricks sorted and mixed by color are laid out in even stacks along the length of the wall for ease of carrying. To control the position, the corners are laid out dry, between which a nylon cord is stretched, along which the position of the masonry is monitored.

The first and last (top) row of bricks are laid out with vents - gaps between every 3-4 bricks that are not filled with mortar (this is only relevant for walls with ventilation gaps). Instead of mortar, wooden plates 1 cm thick are temporarily installed.

The laying is carried out with the brick offset by 1/2 of the length.

Depending on when the facing layer is made - during the construction of the main walls or after that, the facing layer is either tied with the main transverse (bonded) rows through 4-5 ordinary (spoon) rows, or attached to the main wall using anchors fixed in the main wall at the level of the gaps between the bricks and covering the gap by about 8 cm.

Useful video

In this video you will learn how to lay Braer facing bricks:

Conclusion

Braer facing brick is a high-quality, reliable material that provides a protective and decorative function. A variety of colors, textures, a wide choice of material types contribute to creating a stylish look for the house, embodying design ideas and emphasizes favorably architectural features Houses.

The durability and strength of Braer brick will make the walls completely impregnable, protecting them from moisture, frost or mechanical damage.

Bavaria is famous not only for its largest breweries, but also for its unique architecture, represented by castles and town halls. Entire generations of masons lived on its lands, and it was here that new trends in the field of bricklaying were born.

The concept of “Bavarian masonry” has its historical basis. During the period of growing popularity of brick, craftsmen were faced with such a problem as the heterogeneity of the color of the material from different batches (and the batches were very small at that time).

As a result, in order to avoid unsightly spots of different shades, Bavarian craftsmen came up with an original solution - uniformly mixing different bricks (a tone darker or a tone lighter) during the laying process to obtain a variegated background.

Only at first glance it may seem that the bricks are laid out in a chaotic order; in fact, such masonry always maintains a certain rhythm with a predetermined alternation of colors and the ratio of light and dark shades. Concentration of one color should not be allowed (such spots will ruin the entire cladding), as well as a strict geometric pattern.

Features of modern “Bavarian masonry”

Today, in private construction, “Bavarian masonry” is again gaining popularity and a special brick is already used as a facing material, buying which you immediately receive several colors in the batch in equal proportions. Experts have already taken care of the combination of shades and the correct proportions. Depending on your preferences, you can choose a combination of different shades of the same color, or a combination of contrasting colors. In any case, such cladding will become exclusive.

On modern market not only classic collections consisting of 4 colors are presented, but also two-color and multi-color (up to 8 colors and shades). You can experiment with both the color of the bricks and the color of the masonry mortar. In this case, the same set will “play” differently with light or dark seams.

Some of the leading places in Russia in the production of such bricks are occupied by the BRAER, Slavyansky, Golitsynsky and Starooskolsky factories (Recke brand).

Brick factory BRAER (Tula region)

It is the largest manufacturer of bricks that meet international quality standards. The products are manufactured on modern European equipment and have no analogues in Russian market. The company controls all stages of production: extraction of raw materials, design development, implementation innovative technologies(it has its own research laboratory), quality control and sales of its goods.

BRAER produces facing ceramic bricks of all formats from 0.7 NF (euro) to 1.4 NF (one and a half), but the most optimal size for “Bavarian masonry” - 1 NF (single standard). Hollow bricks have high strength (M150), excellent frost resistance (F100) and water absorption of less than 10%.

The full range of BRAER facing bricks is presented at the largest dealer specializing in building materials - Bricus company .

Here at the best prices and with better conditions delivery you can buy the following color options for BRAER bricks:

format 0.7 NF

oak bark with sand (there are small inclusions);
oak bark;
smooth (classic red color with changing tones);
mocha smooth (original gray color).

format 1 NF

reef (has a corrugated surface);
terra (the surface is not smooth, but with shallow depressions);
oak bark;
oak bark with sand;
mocha smooth;
burgundy smooth (4 shades of burgundy);
smooth (brown color with undertones).

format 1.4 NF

smooth (classic).

The retail price per unit of product for 2017 ranges from 20 to 30 rubles (1 square meter will cost 1000-1500 rubles, respectively), which is below the market average.

Slavic brick factory (Krasnodar region)

The plant is equipped with modern German equipment with high productivity. Production is carried out using plastic forming technology. Collections of façade ceramic bricks are distinguished by their unique style and new color schemes, giving the building a presentable appearance and bright individuality.

Hollow brick is presented only in the standard 1 SF format. The manufacturing technology uses the engobing method (applying a thin layer of white or colored clay with additives and dyes to the surface), which increases decorativeness and reduces water absorption to 8%. In addition, Slavic facing brick is characterized by increased strength (M200).

The Bricus catalog presents the following interesting collections: Provence (shades of blue), Hamburg (gray), Gothic and Milan.

Provence smooth with engobing (unusual blue-violet color);
Provence RUST (rustic surface with shallow wrinkles, less bright color compared to Provence);
Provence BUNT ANTIQUE (gradient red-blue color, rustic surface with sand);
Provence ANTIQUE (differs from the previous type only in its uniform blue color);
Provence BUNT RUST (distinguished by the gradient color of the brick with a transition from red to blue);
Hamburg RUST (has a gray background and a rustic surface);
Hamburg BUNT (gradient color with a transition from dark gray to yak brown, smooth surface);
Hamburg BUNT RUST;
Gothic ANTIQUE (rustic surface with sand);
Gothic smooth (bright combination of contrasting colors);
Milan with engobing (each brick is unevenly painted in several colors, smooth surface);
Milano with engobing taupe (smooth surface).

Brick SKZ PROVENCE-ANTIQUE RUST with sand at a facility under construction

The retail price for the manufacturer's product does not exceed 20 rubles per piece, which makes the product very attractive, especially for cladding a private house.

Golitsyn ceramics plant (Moscow region)

It has a century-long history of development and rich experience in brick production. Production lines are constantly modernized, which allows us to produce high-quality building materials in accordance with European standards. The company produces a huge range of products that differ in the method of painting (including two-color), type of surface and size, including non-standard solutions. The facing brick has a strength of M175 and frost resistance of F100, water absorption does not exceed 9%.

The plant produces 5 collections single brick: Bavaria, Country, Old Prague (light milky gray), Milan (dark terracotta), Venice (embossed surface).

The Bricus company offers the most popular options:

Country smooth two-tone;
Old Prague two-tone;
Milan smooth two-tone;
Bavaria RIF two-color;
Wenge smooth.

The price for one brick is 20-25 rubles.

Stary Oskol brick factory (Recke Brickerei brand)

Focused on the production of premium engobed bricks. Maintain product quality at high level allows equipping with modern expensive equipment and active implementation of innovative technologies. Distinctive feature Recke products are characterized by a special color presentation: there are warm tones that transport you to the distant past, and glossy metallic shimmers from the technological future.

Recke facing bricks have a strength of M200 or M250 and a water absorption of less than 6%.

The “Bavarian masonry” brick catalog on the Brikus website is presented with hollow decorative bricks of format 1 NF of the following types:

red-brown;
grey-beige-brown;
yellow-brown (2 options);
brown-yellow.

All material has a smooth surface, which can be glossy or matte. The price for such a brick is 39 rubles, which is quite natural.

All product parameters. Facing brick, hollow.

Format 0.7 NF (Euro format), 250x85x65 mm.
Weight 1.7 kg/pcs. Quantity on pallet: 600 pcs. Loading rate for 20 t vehicle: 11,400 pcs.

Format 1 NF (single), 250x120x65 mm.
Weight 2.3 kg/pcs. Quantity on pallet: 420/448/480 pcs. Loading rate for 20 t vehicle: 7,560 / 8,400 / 8,640 pcs.
Quantity per 1 m2: approx. 50 pcs.

Format 1.4 NF (one and a half), 250x120x88 mm.
Weight 3.1 kg/pcs. Quantity on pallet: 352 pcs. Loading rate for a 20 t vehicle: 6,336 pcs.
Quantity per 1 m2: approx. 38-40 pcs.
The calculation of the amount of brick in 1 m2 is given taking into account the joint width of 10-12 mm!

Properties. Strength grade: M 150-175. Frost resistance: F 100. Water absorption: 8-9%.
Color: red flush (Bavarian masonry).
Surface type: smooth.
General information. Manufacturer: BRAER plant, Russia. Products are certified. GOST 530-2012.

Facing brick Bavarian masonry (smooth) is used for finishing walls and buildings of any intended purpose. It applies:

in private housing construction (buildings 1-3 floors);
for cladding the facades of multi-storey buildings;
for carrying out interior work(when decorating the interior);
when decorating the foundation, columns and other elements.

Distinctive feature of this material is the color. Due to uneven firing in the kiln, as well as oxygen starvation, it is possible to achieve about 6-8 shades with different tints.

Today Bavarian masonry burgundy and red with a smooth surface are produced.

The final appearance of the resulting brick facade is also influenced by the color of the selected grout and the shape of the seams (concave, protruding beyond the boundaries of the facing brick, undercut, etc.). Therefore, everything should be thought through at the stage of designing a brick facade.

Joint jointing performs not only an aesthetic, but also a protective function, since it prevents the penetration of moisture, which over time destroys the masonry at subzero temperatures. Thus, it is possible to significantly increase service life buildings.

Our company’s specialists provide a range of services for the development of a new project, taking into account all the customer’s preferences. In case you already have ready-made solution that requires improvement, our managers will help you improve it and correctly formulate your order. To receive a free consultation, contact us using the contact information provided on the website. Samples of the materials you are interested in can be found in the showroom of the BRIER brick company.

Facing brick production technology Bavarian masonry with a smooth surface

Bavarian masonry bricks are produced in the modern, rapidly developing BRAER plant using latest technologies. It is equipped with imported (mainly German and Japanese) robotic equipment, which significantly improves the quality characteristics of the materials produced, and also allows for the rejection of material that does not meet the standards and requirements at the early stages of production, sending it for recycling.

Smooth brick Bavarian masonry BRAER is available in three formats - 0.7 NF, 1 NF, 1.4 NF. This corresponds to the following dimensions:

250 x 85 x 65 mm;
250 x 120 x 65 mm;
250 x 120 x 88 mm.

This size range expands the scope of application of bricks and allows you to implement a variety of design projects. For example, three-layer masonry can be done with Euro-format bricks.

The raw materials are extracted from our own clay quarry, located two kilometers from the plant in the Tula region, after which they undergo preliminary testing in the laboratory.

All products comply with GOST 530-2012 and have certificates. Therefore, ceramic facing bricks do not emit substances harmful to health.

Characteristics of smooth brick Bavarian masonry and examples of houses

The material has the following properties:

low thermal conductivity;
frost resistance - more than 100 cycles;
high strength, since the brick is resistant to aggressive environmental influences;
moisture resistance (due to which freezing, cracks and fungus formation are excluded);
original appearance;
brickwork does not require additional maintenance, and its service life is approximately 150 years.

The BRAER brick company is the official distributor of the manufacturer's plant. We strive to create the most comfortable conditions for mutually beneficial cooperation, therefore we provide clients with a range of services, as well as special discounts on Bavarian masonry bricks. Photos of houses can be viewed in our catalogue.