How to make a lamp yourself from an ordinary garland in a few minutes? How to make a night light with your own hands - various examples with photo ideas Night light from a New Year's garland.

The garland that is most often used to decorate the New Year tree can be used as a component for making lighting fixture. A DIY garland lamp is easy to make.

To make a lamp you will need a garland, a plastic lampshade and a stand.

At the same time, the lighting in the room will be soft. This lamp can be used as a night light. The designs of such homemade lamps can be varied depending on imagination and source materials.

Lamp made of disks and garlands: production

The following materials will be required:

• CDs or DVDs that have no graphics on both sides;
• garland for 15-20 light bulbs;
• glue and a gun for applying it.

The assembly of such a lighting device should begin by making a geometric figure, for example, a cube or a three-dimensional pentagon, which will serve as the basis. To do this, apply glue to the disk and immediately apply another one. The discs are sequentially glued together until the desired shape is obtained. But, in order to make it more convenient to place inside the cube, one of its sides should not be sealed.

To attach the disks you will need a glue gun or wire.

After all the disks are glued together, a garland is placed inside. It is positioned in such a way that the plug and control box are in the window formed by the joint. Several light bulbs come out into the holes. The number of windows placed inside can be from 3 to 5, depending on the size of the light bulb. The luminous elements must completely fill the hole, thereby creating the desired effect. The remaining part of the garland that does not fit into the holes is placed evenly inside the cube. You should leave a few more bulbs in order to thread them through the last line, which is formed after gluing the last disk.

For ease of installation inside the holes, they can be secured together with tape or insulating tape. In addition, the resulting group can additionally be secured with glue or sealant during their placement in the lamp disks.

After all the holes are filled with light bulbs, you should glue last part lamp cube. The light bulbs left for this purpose are threaded into the last disk.

You can use another disk as a stand. The resulting cube is glued onto it using glue, placing it on an edge. This placement will allow the lighting fixture to stand stably in the future. In this case, it should be taken into account that the socket and control box are placed at the bottom, but are not glued.

After the structure is installed on the stand and the glue has completely hardened, the lamp is ready for use.

Return to contents

Lamp made of plastic packaging and garlands

In order to make this model, the following materials and tools are needed:

1. Warp. It can be used as a plastic bottle of any size or a plastic packaging box of various shapes, for example, a pyramid-shaped candy box.
2. A garland, the number of bulbs in which depends on the size and shape of the chosen base.
3. White paint. It is advisable that the paint be in a can. This will allow it to be evenly distributed over the entire surface in an even layer.
4. Soldering iron with a sharp tip (or electric drill and drill bit diameter).
5. Construction knife.

Before making the slots, markings must be made. They can be placed symmetrically and 1 piece per hole (or in the form of any pattern with several pieces inside). On the base at the bottom it is necessary to make a cut through which a wire with a socket and a control box will subsequently be passed.

If the material from which the base is made allows you to make holes using a soldering iron without damaging it, then it is better to use it. If the integrity of the structure is damaged when exposed to a heated soldering iron, it is necessary to use a drill and a drill for work. According to the markings, holes are made using the tool that is suitable for the selected base.

If, as a result of making holes, sharp edges are formed or part of the plastic remains outside or inside, then these remains must be carefully cut off using a construction knife. This must be done carefully and in such a way as not to damage the rest of the base.

After the processing of the grooves is completed, you can begin painting. The base needs to be painted several times so that a uniform white over the entire surface.

After the paint has dried, you can place the light bulbs in the holes.

For ease of work, you should start from the top. After all the light bulbs are placed and the wire with the socket and control box are placed in the slot, the base should be covered with a lid. This will allow you to move the lamp around the room. The lamp is ready for use.

Every year we buy new toys for the Christmas tree, occasionally we update the garlands... And now - a bunch of them have already accumulated New Year's decorations, which would be a pity to throw away and seem to have nowhere to hang on the Christmas tree... If you also have a transparent glass vase, then you can make a New Year’s lamp out of all this.

Materials:

• Glass transparent vase (small aquarium)
• Garland
• Christmas toys
• Mushura
• If available, branches from an artificial Christmas tree

I saw the idea for a lamp made from a vase somewhere on the Internet. And then I just remembered...

Wash and wipe the vase dry.

Put some tinsel on the bottom

Lay the end of the garland in a circle

Let's start putting away the toys.

It would look more original if the toys were laid out in layers, i.e. in the first layer - identical ones, in the second - different toys, but also identical. Or put fir branches as the second layer, and toys again as the third.

Unfortunately, I didn’t have any branches - a piece of the top of the tree cut off can’t be counted - so I had to limit myself to tinsel and toys

We also place a garland in a circle on the layer of toys and decorate it a little with tinsel. My tinsel is long, so I cut off very short pieces - about five centimeters

Main: Do not compact the layers!!! We place it loosely so that there is air circulation.

Fill the vase almost to the very top. The garland is completely placed in the vase - only the switch for the flashing modes of the light bulbs remains outside. We place it on the side of the lamp that will be the back.

Decorate the top with the last layer of tinsel and close the switch

Put it in a suitable place and get in the pre-holiday mood!

And this is how it shines in the dark

PS. After the publication of the article, many questions arose about the fire hazard of such a structure. I deliberately kept the lamp on for about 6 hours. During this time there were no signs of overheating. There is quite a lot of empty space in the lamp - it is decorated with tinsel - so there is good air circulation there.

Again, the answer is logical: the garland on an artificial Christmas tree doesn’t scare you, does it? But she lies right on the Christmas tree branches, also in contact with toys and hung with tinsel? In addition, now you can safely buy LED garlands that do not heat up at all and do not pose a danger.

Do you remember catching fireflies as a child? Even from a distance, these tiny creatures look magical, and if you still manage to catch a couple of them in a jar... Agree, there is something magical about the miniature lights sparkling from behind the glass.

Now you hardly have time for these cute children's fun. And the season, to put it mildly, is not very conducive. But you can enjoy the magical light from behind the glass at any time. To do this, you don’t have to look for any special lamp - it’s easy to make it yourself.

Today you will learn how to make a beautiful New Year's lamp from a garland in a jar, bottle, vase or other glass container. We have selected 46 photos of the most beautiful examples and will tell you in detail how to do this.

You don't need to be a handmade artist to create this beauty. The technology is simple enough that even a beginner can master it. The materials you will also need are the simplest: a glass container of your choice and a New Year's garland.

Important Notes:

1. It is better to give preference to an LED garland - it does not heat up, and, accordingly, is safer for a closed container.

2. Some options do not include a power cable outlet. So look for a short, battery-powered garland.

__________________________

1. Lamp from a garland in a jar

The best part about this idea is that you probably already have at least one required item. The jar does not have to be beautiful in itself, although interesting models with embossed walls or colored glass are welcome. So sort out the deposits of cans in the pantry - New Year's magic begins!

Materials and tools:

glass jar with a neck wide enough for the palm to pass freely (preferably with small reserve), transparent silicone-based glue, short battery-powered garland.

How to make a lamp in a jar with your own hands:

1. Wash the jar thoroughly and remove the labels. Dry.

2. Apply the garland to the outer wall to outline the intended outline. When you are ready, apply glue to the necessary parts of the garland and fix it inside the jar.

Ready! Now you have your own “winter firefly trap”. This lamp looks especially impressive in the twilight.

Such lamps look great on their own - for example, in the middle of a table. But, if you want a particularly New Year's mood, place the jars on a tray with other seasonal decor: pine cones, fir branches. Artificial snow will ideally complement the composition. Cover the edges of the jar with it or pour it inside - it will turn out no worse than souvenir snow globes.

__________________________

2. Light garland under the serving hood

Their main difference is the ability to give special significance to what is hidden under glass. Just imagine: an ordinary garland will look like a museum exhibit!

For this idea, you can simply put the garland inside, turning the cap over, or glue it, as in the previous paragraph - in this case the composition will look even more impressive.

The most sophisticated option will be with miniature light bulbs in the shape of flowers - if you manage to find such a garland, it will be just wonderful. The cap can not only be placed on a table or chest of drawers, but also built into a New Year’s composition, as in the photo.

__________________________

3. Decorative lamp made of garland and glass vase

Who said that vases are only suitable for flowers? A simple transparent vase without decoration is an excellent basis for any composition. Especially New Year's - behind the glass the bright lights will look simply magical.

This idea is especially good for its practicality: it does not require gluing or “modifying” the vessel, and after the holidays you will be able to use the vase for its intended purpose again.

Everything here is extremely simple: find a suitable glass vase or flowerpot and beautifully arrange the garland inside. The garland can either fill the entire vase or hang beautifully along the edges if the vase is tall. The composition can be supplemented with any suitable filler: pine cones, fir branches, artificial snow...

Do you want to stay in touch with us every day? Welcome to our Planet of Inspiration VKontakte! Take a look, scroll through! Like? Join and get inspired every day!

__________________________

4. Lanterns for shaped candles + garlands

Lanterns occupy a special place in winter decor. There is something fabulously romantic in its outlines - especially in our time, when many people use flashlights. But this is not a reason to throw such a wonderful item into the closet! Bring out some old garden lanterns from the depths of your closet or buy them from IKEA to feel like a Christmas fairy with a magical lantern.

Making a lantern magical is not at all difficult: just place the garland beautifully inside, as in the point about vases. Do you want a special touch? Glue the garland to the walls so that it takes an interesting shape (see point 1). The lantern itself can also be decorated with a bright bow or a New Year's wreath made of pine needles.

__________________________

5. Decorative lamp from a bottle

And this is, perhaps, the most interesting lamp from the garland: in a bottle. It is somewhat more difficult to manufacture than previous options, but the impression more than makes up for all the inconvenience. Just imagine: tiny lights, white or multi-colored, flickering through dark glass... Wine bottles are best suited, but cognac and liqueur bottles look no less impressive.

Materials and tools:

empty glass bottle, drill, glass drill bit (~ 1.25 cm), electrical tape, short garland (preferably battery-powered, not powered).

Precautions: For safety, wear gloves and safety glasses in case the bottle breaks. For the same reason, keep a few spare bottles on hand.

How to make a decorative lamp from a bottle with your own hands:

1. Wash the bottle thoroughly, removing the label, and wipe dry.

2. Mark the place for drilling (3-5 cm from the bottom edge of the bottle) with electrical tape. It is necessary so that the drill does not slip during the process.

3. Secure the bottle (for example, between wooden spacers) and start drilling. Avoid pressing too hard to avoid damaging the glass! Drilling a hole takes about half an hour.

4. Rinse the bottle thoroughly so that no glass chips remain on the walls, and dry. To prevent injury, cover the edges of the hole with sealant.

5. Now let's place the garland. Gradually lower it into the opening of the bottle so that the switch (and power cord, if any) remains outside.

Once it's done, congratulations! You have an exquisite decoration for your table or living room interior.

You can use any bottles, both regular and colored glass. Frosted glass and/or covered with artificial snow will look especially festive. This lamp will look equally good in any color variations, but we recommend playing with contrasts. Light glass + multi-colored garland, dark glass + garland with yellow lights, composition of bottles of different sizes...

For aesthetes, we offer this option: bottles made of colored glass, and inside there is a garland, large decorative filler and grape leaves. Incredibly elegant!

If desired, every Internet user will be able to find a large number of training videos that allow you to assemble original lamps that will decorate the room. In these videos, everyone can find the answer to the question of how to make a night light with their own hands.

Having studied the photo of a night light made by yourself, you can be convinced that such products look stylish, attractive and elegant, you will definitely have a desire to start making them yourself.

"Starry Sky"

By choosing this type of lamp, you can be sure that it will be ideal for the bedroom and children's room. To implement this idea, take a three-liter glass jar with a lid and cover it with foil. First, a switched-on flashlight is placed in the jar. Stars are cut out on the foil.

The night light is ready, which means you can start using it, receiving special pleasure and vivid emotions from the space-style setting.

Lace night lights are also quite popular. To create them, a piece of lace is fixed on the jar. A garland or lantern is also placed inside.

Fluffy night light

To create such a product you need to perform the following manipulations:

Many small circles are cut out of fabric (preference should be given to tulle or tulle).

Take a dry and clean lampshade, parallel circles of tulle and tulle are collected into a “rose”. Using glue, the fabric flower is fixed on the lampshade (while fixing the flower, you need to apply just a drop of glue to the center of the rose). This creates a fluffy ball.

A garland or flashlight is placed inside the lampshade.

This version of the lamp will fit perfectly into a child's room. If you wish, you can also involve your child in creating such a night light, this will bring him closer to his parents and significantly improve his mood.

Night light with LEDs - original and unique

If you decide to assemble a night light with LEDs with your own hands, you can rest assured that this solution will fit perfectly into the interior design of any room. The LEDs are connected to a piece of wire.

The two ends of the wire are connected to the finished board. At this stage of work, you must make sure that everything worked out and that the night light really functions.

As for the plug with LEDs, it needs to be put on the tube. It often happens that the diameter of the plug is larger than the tube. Please note that in this case, you will need to make a seal.

Night light in the shape of a flower

The floral night light looks original, elegant and attractive. To create such a night light, any flowers are selected and inserted into the center of each color of the lamp

Here you can fully use your imagination, because you can arrange a bouquet not only in the form of a flower in a pot, but also hang it like a garland.

In any case, such a composition stands out for its originality and attractiveness. appearance. You can watch instructional videos online that allow you to make similar products yourself.

Night light made from scrap materials. Peculiarities

It is quite possible to create a night light with your own hands from scrap materials, because the most important thing here is desire. Consider what is unusual and original design solution will create a favorable atmosphere in the bedroom, and children, in turn, will be able to get rid of fears.

For example, it is quite possible to make a night light from wood. All you need for this:

• log;
• sandpaper;
• saw;
• glue.

Wheels should be made from a log, two wheels - larger than others, using sandpaper, you need to clean them, then you can avoid splinters getting into your fingers. Now you should carefully coat all the necessary holes with glue.

The workpiece is varnished. All that remains to be done is to install the blanks on the rail, and then pass the LED strip through them.

If you want, you can always make your own beautiful night light on batteries. We can safely say that creating such products will not take you more than half an hour.

You yourself must decide on the ideas that interest you most in order to bring them to life. Know that hand-made night lights always look original and attractive.

Photos of night lights with your own hands

Thanks to a variety of handmade ideas, today anyone can make an original lighting fixture for their home with their own hands. Moreover, you can use a wide variety of materials for this that are simply lying around you. This article will talk about how to make a lamp from a Christmas tree garland.

In the process of making such a lamp, the main thing is to have a good imagination, as well as the desire to do something for the home, family and friends with your own hands.

I want a holiday

We all love New Year. And one of its integral attributes is the Christmas tree garland. It will be an excellent light source for a wide variety of lighting fixtures.
Guided by various master classes, from Christmas tree garland and additional materials(discs, threads, etc.) can be made different types lamps:

• ceiling;
• wall;
• desktop;
• floor.

Lamp option

At the same time, the lamp, depending on your wishes, can be made in different designs.
This lamp has a number of advantages:

• gives a soft glow;
• creates a festive mood;
• easy to construct with your own hands;
• you can use both Christmas tree garlands and lighting models on solar powered;

Pay attention! Garlands that run on solar batteries have appeared on sale relatively recently, so few people know about them yet.

• the possibility of using available materials - disks, Christmas tree decorations, etc.;

• With the help of a garland you can make almost any type of lighting fixture yourself.

The resulting lamp can also be used as a night light in a children's room. Here it can be stylized as “fairytale” clouds, flowers, trees, etc.

Stylized sconce

When creating lighting fixtures from garlands and additional materials, you can use any schemes and designs. It all depends on what you can find in your home.

What are we looking for?

You can make a similar lamp using a garland with or without solar batteries using the following materials:

• Christmas tree garland. Even 15-20 light bulbs will be enough. Instead, you can use a solar-powered light source;
• a couple of discs (CD or DVD);

• glue;
• additional materials for decorating a homemade product.

Set of materials

During the manufacturing process, in addition to the materials described above, you will only need a glue gun to carefully apply glue in the right places.
As you can see, all this can almost always be found at home. Therefore, it will be possible to make such a lamp almost for nothing.

Work algorithm

The lighting device that we are considering in this article will always have a garland (Christmas tree or solar-powered) at its core. So, the lamp can be made as follows:

Disc frame

• You can use any geometric shape as a frame. It can be a cube, pentagon, etc.;
• a geometric figure can be easily formed with your own hands from disks. To make the disks into the shape we need, they should be glued together with glue;
• Apply glue to the disk and immediately apply another one to it. We wait until the glue dries and continue to build up the figure using discs;

Pay attention! one side of the figure does not need to be glued. Through this side we will place a light source inside the lighting fixture.

• After the figure is ready, a garland (solar-powered or regular) should be placed inside it. When using a regular garland, the plug and control box should be placed in the window formed by the articulation of the discs. It is also allowed to insert several light bulbs into the holes and joints available in the figure;

Finished lamp

• When installing, the light bulbs must completely fill the existing hole. This will help achieve the desired lighting effect;
• after this, the remaining part of the garland must be evenly distributed over the entire surface of the geometric figure formed from the disks;
• several light bulbs need to be left in order to thread them into the last edge, which is attached to the figure after placing the light source inside it.

To with geometric figure It was more convenient and safer to work while placing the light source inside; all joints can be treated with insulating tape or tape. After completing the assembly of the lighting fixture, all joints can be additionally treated with sealant. This way you will achieve greater strength in the structure you made with your own hands.

Final stage

The last stage, namely the installation of the lamp, varies depending on where and how it will be placed. You can install it with your own hands like this:

Ceiling lamp

• Using durable decorative ropes, the lamp can be attached to the ceiling or wall. In the first case, the resulting lighting fixture can be hung on a ceiling hook, and in the second, you can use the base from a wall sconce;
• if you want to do table lamp or a small night light, then here you can use another disk as a pedestal. In this case, the figure of the lamp must be installed edge-on on a kind of pedestal. This will give it more stability. The lighting fixture should be glued to the stand using glue. At the same time, make sure that the control box and plug are at the bottom and hidden from view by decorative elements or the lamp itself.

It should be noted that this is a rather complex option for creating a lamp; there is a simpler solution.

Simpler doesn't mean worse

This method involves using the most ordinary plastic bottle as a base. It can be of any shape and size. In addition to this, you will need the following materials:

• a garland of the size you need, number of bulbs and color scheme;
• a can of white paint;
• glue. It's better to use superglue;
• tulle.

Forming holes

From your tool kit you should have a soldering iron with a sharp tip and a construction knife.
Making a lamp includes several simple operations:

• on plastic bottle make notes;
• We pass over them with a soldering iron, thus forming regular, neat holes. If it doesn’t work like this, then change the soldering iron to a drill;
• We remove the unevenness of the hole with a construction knife;

• paint the bottle with white paint. We paint in several layers to achieve a uniform color;
• We place a garland with tulle inside the base and connect it. The wire is routed through one hole. Place a lid on top of the bottle. This will allow the lighting fixture to be moved freely around the house.

Finished lamp

There is another fairly simple way. Simply place our light source in a glass vase/jar, alternating it with different decorative materials. For example, these could be plastic Christmas tree decorations. And, in fact, that’s all, the lamp is ready.
A DIY garland lamp can have a non-standard and unusual look. A wide variety of materials are suitable for such a lighting device: soft toys, beads and buttons, glass pebbles, etc. Correctly selected materials will allow you to create a unique play of light and shadows from the lamp in any room of the house.

Making an original bio-fireplace on your own